SGI Analytical Technologies
    Facebook Linked In YouTube

 

shrinkwrap machine, Shrink Wrap Machines, Fully Automatic Shrink Wrap Machine manufacturers & suppliers Mumbai, India

About Shrink Wrap Machines

What is Shrink Wrapping? and How Shrink Wrap Machine works?

Introduction
Shrink Wrap MachineShrink wrapping, bundle wrapping, etc, is a process during which a product item or a group of items in wrapped in a loose sleeve or envelope of plastic film, which upon application of heat shrinks and tightly conforms to the shape of enclosed contents.

Shrink packaging processes is established considering the increasing cost of packaging and to reduce the cost of secondary packaging. Due to it's practical and cost effective advantages, it has found its use in many industries at various stages of packaging process.

Shrink wrap machine consist of Special Stainless Steel Finned tubular heater for Lowest power consumption & Highest heat transfers. Temperature is Controlled with the help of Digital Temperature for Accurate amount of heat. Best Quality Shrink wrapping is obtained with the help of heavy duty blower which provides sufficient amount of heat transfer.

Shrink wrap machine comes with the world class insulating material like Rockwool on the machine panel. The Conveyor rods of the shrink wrapping machine which passes from the hot shrink tunnel is coated with Silicon Tubes.

Shrink wrap machine is Over backed with heat resistant power coating on Mild Steel Fabrication. Selective Model of Shrink wrapping machine comes with Heavy-Duty DC motor with Gear-Box And Special Controller for Heavy Load Bearing Conveyor.

Special Seven Tank process Powder Coated Mild Steel Fabrication Body which make the shrink wrapping machine Heavy Duty and Long Lasting.

 

Shrink Packaging can be divided into following categories

A) Primary- where the product is totally enclosed for protection from abrasion, dust, moisture and for improved appeal.

B) Secondary-
where a group of items is wrapped together to form a Sales unit like cold drink pet bottles of cold drinks, boxes etc

C)Distribution packaging
-
 where product is wrapped into a distribution unit which may stacked directly on the pallet ready for transportation.
When walking through supermarket one only has to look on top of the shelves to see the extent of use of this packaging method.
Most grocery and high volume beverage products will use cardboard trays for added

  1. Rigidity of the pack. While the use tray is not always necessary, it does provide improved handling in automated warehouses.
  1. Shrink Packaging Process
    Shrink wrapping, bundle wrapping, etc, is a process during which a product item or a group of items in wrapped in a loose sleeve or envelope of plastic film, which upon application of heat shrinks and tightly conforms to the shape of enclosed contents.
    The key element of this process is Shrink Film.

    Shrink Film can be made from a variety of materials each having different strength, shrink characteristics transparency and luster.


1, PolyVinylChloride (PVC),
2, PolyPropylene (PP) and
3,PolyEthylene (PE) are the three most commonly available materials.

PVC, Being one of the first materials used, is now being phased out due to its toxic properties, although still used abundantly in underdeveloped countries.

Low Density Polyethylene (LDPE) is best suited for general packaging applications due to it's relatively high strength and low cost.

Polyethylene Shrink film is manufactured in an vertical extrusion process where ethylene granules are heated under pressure to produce Polyethylene polymer.The polymer is forced upwards through a circular extrusion die to produce a very thin walled continuous tube of material, still in a semi-molten state as it emerges from the die.

A controlled supply of air is fed up through the center of the die to stretch the tube in the radial direction, thus forming a bubble. at the same time the tube is stretched in length by winding the film at a faster than it is extruded.

As the film cools, the induced stretch is "memorized" in the film. Upon reheating the film, if unrestrained, will shrink a certain percentage in the width, referred to as % Shrink in TD (transverse direction), and in the length, % shrink in MD(machine direction)

At the top end of the bubble the film tube is cool enough to be flattened and wound off as Lay-flat tubing, alternatively, it can be slit at one edge to produce Center-folded material or slit at both edges to produce Flat sheet.

 

Shrink Wrapping Process

The essential aim of the Shrink wrapping process is to place shrink film around the product prior to shrinking. There are two principle forms of wrapping:

i)Sleeve wrapping –Shrink wrapping bottles ,boxes etc by ready sleeve

ii)Overwrapping – Shrink Wrapping the bottles, boxes etc totally wrapping and shrinking

Sleeve wrapping- Sleeve Shrink Wrapping  - best suited for secondary and tertiary packaging. The process is easily automated, uses low cost material and has low labour input. Sleeve wrapping is readily applied to regular shaped products that need to be collated into larger, easier to handle packs for palletising, warehousing or distribution.

Sleeve wrapping is performed using two rolls of flat sheet shrink film. The ends of the sheets are heat sealed together forming a vertical curtain. Product is pushed through the film curtain to a position behind the Welding bar.

The welding bar descends in front of the pack, completing the sleeve of film, parting the sleeve from the rest of the film and reforming the film curtain for the next pack.

The sleeved pack then passes to the shrink tunnel where film shrinking takes place.
The resultant pack will is Not totally enclosed. Each end of the pack has an opening due to the original wrap being only a sleeve.

 

Sleeve Wrapping Machines (Bundle wrappers)

A wide range of machinery is available and the choice depends on application and budget. Simple manually operated machines are the lowest level. In use they require the operator to position the product, operate the jaw, by means of a pull bar or a foot pedal initiate the seal cycle and release the Jaw.
At the next level are operator controlled semi- automatic machines with pneumatic assistance. These require the operator to position the pack and initiate the automatic welding cycle. Medium speed automatic systems are the next option, all machinery cycles being initiated by the arrival of product onto the machine.
This type of machinery features intermittent motion operation and is capable of speeds up to 30 packs/min. High speed continuous motion machinery is available with speeds up to 100 cycles/min.

 

Over wrapping –Shrink Wrapping

Overwrapping Achieves a total enclosure of the product by a perimeter sealing process performed on L-bar type machines that utilize Centre folded film. Total enclosure can also be achieved using flat sheet film on a Flow wrapping machines.

Overwrapping is best suited for low height, rectangular shaped products such as stationery, magazines, video tape, CD's etc. Although the writer has in the past designed L-Bar type machines 2.4m long x 1.2m wide with a suitable 1.35m wide Shrink Tunnel.

When performed on an L-bar sealing machine the operation is as follows The end of the film is sealed across the width and forms one of the sealed sides of the pack. Product is inserted between the layers of film, then transferred together to the sealing station. Here the remaining two sides are sealed and product is now completely enclosed by the film.

From there the package is moved onto the shrink tunnel conveyor to complete the operation. Simple L-Bar machines are manually operated although automatic models are also available.

There are also "All in one" L=Bar type units where the Sealing and shrinking are performed in one operation. The Sealing station consist of a hood, where the product is enclosed in film. Once the seal is complete, Hot air is blown around the pack to shrink the package. These machines are best suited successful in low speed, office or dispatch applications.

B) Shrinking Process
Once the product is wrapped, the plastic film around it has to be shrunk to complete the process.
Shrinking of the film can be achieved through a number of methods which depending on application may range from hand held gas or electric hot air blowers, to fully automated room size ovens.However, the best results are obtained through the use of a Shrink Tunnel.

Shrink Tunnel, is simply a recirculated hot air chamber sitting on top of a conveyor which carries the product through the chamber. The essential requirements for a good shrink tunnel are a constant yet adjustable air temperature and conveyor speed, symetrical air circulation pattern.

As pre-wrapped product is transported through the hot chamber the film temperature raises and the film shrinks to conforms to the shape of enclosed product. At that stage the film is not strong enough to compress the contents.

When the pack emerges from the hot chamber the film cools and shrinks a little more, tightening the pack into a stable, easily handled unit.
The degree of final compression is determined mainly by the thickness and type of film used.

Shrink packaging has been proven and well established for over three decades. Due to its fast process, practical and cost affective advantages, because of the cost effectiveness shrink wrap machines are using in various industries for there packaging.

Our Products

Fully Automatic Shrink-wrap Machine
Fully Automatic Shrink Wrap Machine with Duel / Twin output
Fully Automatic Shrink Wrap Machine with Tray or Box
Semi Automatic Shrink Wrap Machine
Automatic Sleeve Shrink Wrapping Machines
Shrink Wrap Tunnels
Shrink Wrap Films